Slamtec RPLIDAR A1 replacement guide

Independent evaluation guide — not an official Slamtec document. Keyword pairing does not establish equivalence. Source completeness does not establish compatibility or a current commercial offer.

Planning a controlled replacement

A Slamtec RPLIDAR A1 replacement project should begin with a record of the installed component, hardware revision, cable assembly and host software behavior. Determine whether the change is driven by availability, packaging, performance or maintenance before choosing a candidate. ERDI SPD1200ZG appears in the supplied keyword mapping as a discussion candidate only; this page does not claim drop-in compatibility or an approved substitution.

Review mechanical, electrical and software changes as separate work items. Compare mounting features, optical clearance, connector orientation, power requirements and data handling against source documents. Preserve the original configuration and define how to reverse the change if the prototype fails acceptance. A successful distance reading on a workbench does not establish correct operation across the full environment or every host-system error condition.

Agree on a staged validation plan covering startup, normal measurement, invalid results, reconnection and representative field conditions. Retain logs and document any adapter, firmware or calibration changes introduced during the trial. Ask ERDI to review the intended application and the evidence gaps for SPD1200ZG before ordering a production quantity. Approve the substitution only after the responsible system owner has reviewed the test results.

Source-gated comparison

Competitor values use the supplied source URL, capture date and confidence record; ERDI values additionally require a matching source excerpt. Capture dates record retrieval, not publication or revision dates. Missing or unsupported entries stay marked as Not published, describing a gap in the supplied evidence rather than an exhaustive vendor search.

Slamtec RPLIDAR A1 | ERDI SPD1200ZG | parameter verification
ParameterSlamtec RPLIDAR A1ERDI SPD1200ZG
Measurement range (m)0.15~12 m0.1–1200 m
Accuracy (cm)Not published±0.5 m at d ≤100 m; ±(0.5 m + 0.0007d) for 100 m < d <1200 m
Update rate (Hz)Not publishedNot published
Electrical interface and protocolUART, 3.3 V logicUART-TTL; customizable
Supply voltage (V)53.3–5 V
Wavelength (nm)Not publishedNot published
Field of view (deg)Not publishedNot published
Published price (USD)Not publishedNot published

Evidence and limitations

Slamtec RPLIDAR A1 source record

Source: https://www.slamtec.com/en/lidar/a1spec (captured , confidence medium)

ERDI SPD1200ZG source record

SOURCE_URL: https://erdilrf.com/models/spd1200zg/
CAPTURED_AT:

0.1–1200 m | ±0.5 m at d ≤100 m; ±(0.5 m + 0.0007d) for 100 m < d <1200 m | UART-TTL; customizable | 3.3–5 V | 7.2 × 14.7 × 22.3 mm (body; excludes mounting features)

Frequently asked questions

Is ERDI SPD1200ZG a drop-in replacement for RPLIDAR A1?

No drop-in claim is made. Mechanical, electrical, protocol and system behavior require separate review and acceptance testing for the actual application.

Why are some RPLIDAR A1 comparison cells marked Not published?

The supplied parameter record lacks a usable value or complete source metadata. ERDI entries additionally require a supporting source excerpt. These are evidence gaps in this record, not zero values and not proof that the feature is absent.

How do I ask ERDI about SPD1200ZG?

Use the model link to review the candidate, then send the intended application, target conditions, host interface and quantity through the contact page. Request the applicable documents and a scoped assessment rather than assuming compatibility.

Discuss the ERDI candidate

Provide the required measurement function and operating conditions so the candidate can be assessed against the application. Model names and this planning association alone do not constitute a compatibility recommendation.