The Benewake TF02-Pro is a 40 m single-point ToF sensor in an IP65 housing on a 5 to 12 V supply. The closest ERDI part is the LRF50H, which reaches 50 m at 90% reflectivity, samples at 1 kHz by default and costs $100 for 1 to 19 pieces, shipping included. If you need a 3.3 to 5 V board with I2C, the LRF50VB is the smaller choice at $70.
Specification comparison
| Parameter | Benewake TF02-Pro (source) | LRF50H | LRF50VB |
|---|---|---|---|
| Range | 0.1 to 40 m at 90% reflectivity | 0.05 to 50 m at 90%; 0.05 to 15 m at 10% | 0.05 to 50 m at 90%; 0.05 to 20 m at 10% |
| Blind zone | 10 cm | 5 cm | 5 cm |
| Frame rate | 1 to 1,000 Hz | 20 Hz to 10 kHz (default 1 kHz) | 100 Hz |
| Accuracy | Not stated on the product page | ±5 cm (<10 m); 1% (≥10 m), 2σ | ±5 cm (<5 m); 1% (≥5 m) |
| Ambient light | Up to 100 klux | 45 m at 100 klx | 10 m at 60 klx |
| Interface | UART, I2C | UART | UART / I2C |
| Supply | DC 5 to 12 V, reverse-connection protection | 9 to 36 V DC | 3.3 to 5 V DC |
| Protection | IP65 | No rating stated | No rating stated |
| Weight and size | Not stated on the product page | 15 +/- 2 g; 38 x 20 x 30 mm | 1.3 g; 18.7 x 11.8 x 13.3 mm |
| Price (USD) | Not published on the maker page | $100 for 1 to 19 pcs; $50 from 1,000 pcs | $70 for 1 to 19 pcs; $20 from 1,000 pcs |
Which one fits which job
TF02-Pro fits a sealed outdoor mount where you cannot add a housing: it has an IP65 rating, a 5 to 12 V input, and Benewake parts have built-in drivers in common flight-controller firmware. LRF50H fits a 12 or 24 V machine rail (9 to 36 V in), a longer 50 m reach, and sampling above 1 kHz when you average readings. LRF50VB fits a small board that already runs 3.3 or 5 V and needs I2C, at 1.3 g.
Price
Benewake does not print a price on the TF02-Pro page (it links to a buy button), so compare against a current distributor quote. ERDI prices are public and shipping is included: LRF50H runs $100 for 1 to 19 pieces, $90 for 20 to 30, $80 for 31 to 500 and $50 from 1,000. The LRF50VB runs $70 down to $20.
Integration notes
- LRF50H and LRF50VB: UART at 460,800 baud by default (adjustable), 8N1, frame header 0x5C, distance as a little-endian value, checksum is the inverted sum of the bytes from the second to the second-last. The LRF22VB I2C address is 0x52 in its datasheet.
- The LRF50H datasheet gives a 9 to 36 V supply but does not state the UART signal level. Ask us to confirm it before wiring to a 3.3 V flight controller.
- ERDI modules are not on the built-in rangefinder list of ArduPilot yet. A driver pull request (ArduPilot #34983) was open on 2026-11-13. Until it merges, use the reference drivers in github.com/ErdiTech/erdi-lrf-drivers and the Pixhawk wiring guide.
- Typical wire: LRF50H uses a 5-pin 1.25 mm terminal with 50 cm tinned wire.
Sources and dates
- Benewake TF02-Pro: https://en.benewake.com/TF02Pro/index.html, read 2026-11-13.
- ERDI values: the model pages linked above and the published catalog, captured 2026-10-08, prices checked 2026-11-13.
Competitor values are the ones printed on the maker’s public page on the date shown. They may change, and test conditions differ between makers, so confirm against the current datasheet before you design in either part.
Frequently asked questions
Is there a cheaper alternative to the Benewake TF02-Pro?
ERDI LRF50H covers 50 m at 90% reflectivity for $100 at 1 to 19 pieces and $50 from 1,000. The LRF50VB is $70 at 1 to 19 pieces. Benewake does not publish a TF02-Pro price on its own page, so get a current quote for the like-for-like comparison.
Can I power the ERDI LRF50H from 5 V like the TF02-Pro?
No. The LRF50H needs 9 to 36 V DC. For a 3.3 to 5 V supply choose the LRF50VB (3.3 to 5 V) or the LRF22VB (3.0 to 3.6 V).
Do ERDI short-range modules have I2C like the TF02-Pro?
The LRF50H is UART only. The LRF50VB and LRF22VB offer UART and I2C. The I2C address for the LRF22VB is 0x52 in its datasheet.
Is the ERDI module sealed like the TF02-Pro with IP65?
Benewake states IP65 for the TF02-Pro. The LRF50H and LRF50VB datasheets list no protection rating, so plan a housing or enclosure window for dust and spray.
What is the default baud rate of the ERDI H and VB series?
460,800 baud, 8 data bits, 1 stop bit, adjustable, with frame header 0x5C. The protocol and sample drivers are in the ErdiTech driver repository.
Where to go next
Model pages: LRF50H, LRF50VB, LRF22VB, LRF200H. To filter the whole range by distance, wavelength and interface, use the selector. Other comparisons are on the comparison hub, and every model price is on the price page. For a quote or a sample, email tommy@erdimail.com or use the contact page.