Skip to main content
Explore ERDILRF
ERDILRF LaserOptics. Electronics. Integration.
Products
905 nm sensors & rangefindersLR seriesSPD seriesH seriesVB seriesLRF A seriesOther product platforms1.54 µm laser sources1535 nm rangefindersAll products
Applications
Application overviewOptical observationCivil UAVsSite monitoringIndustrial sensingHandheld instrumentsField measurement
Insights
Product SpotlightEngineering knowledgeProduct filmsInside ERDILRF
Support
Technical supportFrequently asked questionsModel selectorContact our team
Downloads
All downloadsDrivers & integrationDeveloper docsEngineering community (Q&A)Specifications & CAD
How to buy
Samples & quotationsPrice listCompare modulesDealer programRequest a sample
Company
About ERDILRFCertificatesContact usPrivacy policyTerms
Talk to Sales

Press ↑↓ to move, Enter to open, Esc to close.

Published range
4–1,000 mStandard range; actual reach depends on target and environment.
Interface
UART-TTLCustom configurations are specified separately.
Wavelength
905 ± 5 nm
Weight
≤10 g

The details

LR1000E2 specifications

Read every value with its conditions. View the model documents for integration.

LR1000E2 Specifications

LR1000E2 LR1000E2 Specifications
ParameterSpecification & conditions
Laser wavelength905 ± 5 nm
Measurement range4–1,000 mStandard range; actual reach depends on target and environment.
Ranging accuracy±1 m (D ≤ 400 m); ±(1 + 0.001D) m (D > 400 m)Whiteboard target, 90% reflectivity: 2.3 × 2.3 m for the first distance interval; 2.3 × 4.6 m for the second.
Measurement update rate3–10 Hz (adaptive)Completed distance outputs; not the optical pulse-repetition rate.
Communication interfaceUART-TTLCustom configurations are specified separately.
Baud rate115200 bps
Supply voltage3.3–5 V
Operating temperature−20 °C to +55 °C
Storage temperature−40 °C to +60 °C
Mechanical drawing dimensions25.7 × 13.3 × 24.6 mmDrawing nominal values. Observe the individual tolerances in the model drawing; do not machine from the rounded summary alone.
Weight≤10 g
Ingress protectionIP67Lens cavity only; not a blanket rating for the exposed board or the complete host product.
Laser safety classClass 1As stated in the model manual; finished-equipment assessment is separate.
Laser beam divergence< 9 mrad
Optical materialResin Aspheric Lens
Receiver aperture9.2 mm × 14.5 mm
Startup time≤ 200 ms
Inrush current< 350 mA
Sleep power consumption< 1 mW
Standby power consumption< 0.3 W
Short-range power consumption< 0.6 W
Operating power consumption≤ 1 W

Documents

Document notes & versions
ENGINEERING FILES

Technical Downloads

Use the current document revision for design review and confirm the ordered connector and mechanical configuration before release.

Product overview

LR1000E2 905 nm Laser Rangefinder Module

LR1000E2 is a laser rangefinder module for OEM integration, with a published test range of 1 km and a UART interface. Confirm target conditions, configuration and the current datasheet before integration.

LR1000E2 is the entry 905 nm module in our E family: 4–1000 m, ≤10 g and 25.7 × 13.3 × 24.6 mm, for drones, handheld meters and robots that need kilometre ranging from 3.3–5 V.

WhatsApp about LR1000E2
From $30 USD / unitLowest published unit price at 501+ pieces. Shipping included.
B2B PURCHASING

Volume Pricing

Published unit prices apply only to the stated quantity band. Configuration, qualification, tax and Incoterm details are confirmed in the quotation.

USD / unit
1–30 piecesBase tier$80 USDPublished unit price
31–200 pieces$60 USDSave 25%
201–500 pieces$40 USDSave 50%
501+ piecesLowest unit price$30 USDLowest published price · Save 63%
Commercial terms and lead time are confirmed in the quotation.

Integration library

Go into the details.

Drawings, test conditions and application notes. Open the part you need.

Selection
SELECTION

Choosing LR1000E2 against nearby models

Within the E2 build, LR1200E2 adds 200 m and a tighter <4 mrad beam (against <9 mrad here). LR1000E4 has identical optics and electronics in the taller 25.7 × 14.2 × 26.2 mm E4 body.

For a cylindrical housing with IP67-protected optics, see LR1000D23 (Ø23 × 47 mm, ≈20 g).

Published unit prices start at $30 at 501+ pieces; see Volume Pricing for all quantity bands.

Technical documentation & drawings
SPECIFICATIONS

LR1000E2 datasheet values

Figures are reproduced from the LR1000E2 datasheet. Read each value together with the test condition printed beside it.

ParameterValueConditions / notes
Laser wavelength905 ± 5 nm—
Measurement range4–1000 mStandard range; actual reach depends on target and environment.
Ranging accuracy±1 m (D ≤ 400 m); ±(1 + 0.001D) m (D > 400 m)Whiteboard target, 90% reflectivity: 2.3 × 2.3 m for the first distance interval; 2.3 × 4.6 m for the second.
Measurement update rate3–10 Hz (adaptive)Completed distance outputs; not the optical pulse-repetition rate.
Communication interfaceUART-TTLCustom configurations are specified separately.
Baud rate115200 bps—
Supply voltage3.3–5 V—
Operating temperature−20 °C to +55 °C—
Storage temperature−40 °C to +60 °C—
Mechanical drawing dimensions25.7 × 13.3 × 24.6 mmDrawing nominal values. Observe the individual tolerances in the model drawing; do not machine from the rounded summary alone.
Weight≤10 g—
Ingress protectionIP67Lens cavity only; not a blanket rating for the exposed board or the complete host product.
Laser safety classClass 1As stated in the model manual; finished-equipment assessment is separate.
Laser beam divergence< 9 mrad—
Optical materialResin Aspheric Lens—
Receiver aperture9.2 mm × 14.5 mm—
Startup time≤ 200 ms—
Inrush current< 350 mA—
Sleep power consumption< 1 mW—
Standby power consumption< 0.3 W—
Short-range power consumption< 0.6 W—
Operating power consumption≤ 1 W—

Operation and Data Output

Single-shot mode requests one reported distance. For a weak return, the manual describes repeated internal measurements before reporting stable distance data. Continuous mode produces repeated results at the documented adaptive update rate.

The standard measurement-rate specification is 3–10 Hz (adaptive). Use the current protocol table for command timing and output format.

Electrical Interface

PinSignalFunction
1GNDPower ground
2VCCPower input
3I/O (Reserved)Reserved for expansion
4TXDTransmit data: module → host
5RXDReceive data: host → module
6SW-SHOTFunction-enable input. The required control polarity must match the supplied configuration.

Mechanical Dimensions

Use the drawing and its tolerances for installation. This drawing is reproduced directly from the current LR1000E2 user manual.

LR1000E2 mechanical drawing, current user manual page 4
LR1000E2 Mechanical DrawingManual page 4. Open the PDF to inspect the original dimensions and tolerances.
Integration checklist
INTEGRATION

Integrating LR1000E2 into your design

  • Supply: 3.3–5 V; sleep below 1 mW.
  • UART-TTL at 115200 bps.
  • Output: 3–10 Hz adaptive completed distances.
  • Accuracy: ±1 m up to 400 m, then ±(1 + 0.001D) m, measured on a 90% whiteboard. Operating temperature −20 °C to +55 °C.

When exporting software events, keep the event kind and leave a missing distance blank instead of replacing it with zero. Our offline JSON-to-CSV example keeps numeric 0.0 separate from absence using synthetic events from the retained LR1000E2 parser profile. It does not validate supplied firmware or measurement performance.

Applications
APPLICATIONS

Where LR1000E2 is used

  • Drone altitude and payload ranging. Light enough for small airframes.
  • Golf and outdoor meters. Kilometre range in a handheld.
  • Robotics. Long-range distance for outdoor robots and vehicles.
Questions & answers
FAQ

LR1000E2 integration questions

LR1000E2 or LR1000E4?

Same performance; E2 is 13.3 mm thick, E4 is 14.2 mm and slightly taller. Choose by your bracket.

Why is the beam wider than on LR1200E2?

LR1000E2 lists <9 mrad; LR1200E2 lists <4 mrad. A wider beam is more forgiving on aim but spreads energy over a larger spot.

Can the UART connect to RS-232?

Not directly; use a level shifter or transceiver.

HARDWARE

LR1000E2 mounting, wiring and commands

Taken from the LR1000E2 outline drawing and user manual. Check hole positions against the drawing or the STEP file before machining a bracket.

Mounting

Two M1.4 threaded mounting holes between the transmitter and receiver windows. Hole depth and spacing are not dimensioned on the drawing.

Request the LR1000E2 STEP model for your bracket design.

Pin definition

PinSignalWireConnection
1GNDblackpower -
2VCCredpower +, 3.3-5 V (shipped harness: 5 V)
3I/O (reserved)grey or darkleave unconnected
4TXDwhitemodule TX, connect to host RX
5RXDgreenmodule RX, connect to host TX
6SW-SHOTyellowmust be held high: tie to the same supply as VCC (factory-confirmed wiring for current units)

Serial settings

Logic level
3.3 V logic
Default baud rate
115200 bit/s
Checksum
Send frames: low 8 bits of the sum of bytes 3 to 7. Reply frames: low 8 bits of the sum of bytes 1 to 7.

Common commands

CommandSend (hex)Reply (hex)Notes
Single measurement55 AA 88 FF FF FF FF 8455 AA 88 STA FF DIS_H DIS_L SUM[1:7]STA = 1: success. DIS_H/DIS_L = distance high/low byte; the reported value is 10 x the measured value.
Continuous measurement55 AA 89 FF FF FF FF 8555 AA 89 STA FF DIS_H DIS_L SUM[1:7]STA = 1: success. DIS_H/DIS_L = distance high/low byte; the reported value is 10 x the measured value.
Stop measurement55 AA 8E FF FF FF FF 8A55 AA 8E STA FF FF FF SUM[1:7]STA = 1: stopped; STA = 0: failed.

Frames follow the LR1000E2 user manual; every full frame has been checked against the manual's checksum rule. Open-source drivers: Drivers & wiring.

Engineering Q&A

Questions about LR1000E2

Answered by ERDI engineers in the community.

Ask an engineer about LR1000E2

LR1000E2 quick answers

How much does the LR1000E2 weigh?
≤10 g.
What power does the LR1000E2 need?
Supply: 3.3–5 V.
Which interface does the LR1000E2 use?
UART-TTL.
How much does one LR1000E2 cost?
$80 for 1 piece, shipping included. Volume price from $30 at 501+ pieces.
What is the minimum order for the LR1000E2?
1 piece. Pay online by card or PayPal, or by bank transfer; shipping is free worldwide.
What is the LR1000E2 lead time?
Standard warranty: one year. The lead time is stated on your proforma invoice (PI) before you pay.

Laser safety & status

Laser class
Class 1 (IEC 60825-1)
Status
Available to order

Laser class as stated in the module document. Classification of your finished product depends on its optical path and configuration.

ERDI TECH

Manufacturer · Chengdu · Founded 2021

Evidence-backed certifications: ISO 9001 · CE EMC

Technical inquiry

Discuss LR1000E2 for your application.

Share the target, range, interface and expected quantity. Your selected model stays attached to the inquiry.

Request a review or quotation

Start with your work email and one line about the module or application. Add technical details if you have them.

No models attached.Name the models you are comparing in the requirement, or send the requirement without one.
Send me
Add technical requirements (optional)
Add project & contact details (optional)
Preparing the form. You can also send your request by email.

We reply within one business day (Chengdu, UTC+8).