Skip to main content
Explore ERDILRF
ERDILRF LaserOptics. Electronics. Integration.
Products
905 nm sensors & rangefindersLR seriesSPD seriesH seriesVB seriesLRF A seriesOther product platforms1.54 µm laser sources1535 nm rangefindersAll products
Applications
Application overviewOptical observationCivil UAVsSite monitoringIndustrial sensingHandheld instrumentsField measurement
Insights
Product SpotlightEngineering knowledgeProduct filmsInside ERDILRF
Support
Technical supportFrequently asked questionsModel selectorContact our team
Downloads
All downloadsDrivers & integrationDeveloper docsEngineering community (Q&A)Specifications & CAD
How to buy
Samples & quotationsPrice listCompare modulesDealer programRequest a sample
Company
About ERDILRFCertificatesContact usPrivacy policyTerms
Talk to Sales

Press ↑↓ to move, Enter to open, Esc to close.

LRF1200A1 is a 905 nm laser rangefinder module from ERDI LASER. Published range: 5–1200 m. Ranging accuracy: ±1 m (5 m ≤ L ≤ 100 m); ±(1 + 0.004L) m (L > 100 m). Interface: UART, 3.3 V TTL. From $35 per unit, shipping included (lowest published tier, 501+ pieces; see the volume table below). Updated: 2026-11-06.

How LRF1200A1 differs from neighboring models

ItemLRF1200A1LR1200E4
Range5–1200 m4–1200 m
Accuracy±1 m (5 m ≤ L ≤ 100 m); ±(1 + 0.004L) m (L > 100 m)±1 m (D ≤ 400 m); ±(1 + 0.001D) m (D > 400 m)
Beam divergence—< 4 mrad (small laser spot)
InterfaceUART, 3.3 V TTLUART-TTL
Supply3.3 V ± 0.1 V3.3–5 V
SizeØ23 × 40 mm25.7 × 14.2 × 26.2 mm
Published priceFrom $35 USD / unitFrom $35 USD / unit

Related models: LR1200E4.

LRF1200A1 frequently asked questions

What is the measurement range of the LRF1200A1?
The published range is 5–1200 m. Actual reach depends on target reflectivity, size and visibility.
What laser wavelength and interface does the LRF1200A1 use?
Wavelength: 905 nm. Interface: UART, 3.3 V TTL. Supply: 3.3 V ± 0.1 V.
How accurate is the LRF1200A1?
Published ranging accuracy: ±1 m (5 m ≤ L ≤ 100 m); ±(1 + 0.004L) m (L > 100 m). Update rate: 1–3 Hz.
How much does the LRF1200A1 cost?
From $35 per unit, shipping included, at 501+ pieces. Smaller quantities use the higher tiers in the volume table (single-piece tier: $90).
What laser safety class is stated for the LRF1200A1?
Class 1
Published range
5–1,200 mBuilding target; the source table gives ≥5–1200 m.
Interface
UART, 3.3 V TTL
Wavelength
905 nm
Weight
18 g

The details

LRF1200A1 specifications

Read every value with its conditions. View the model documents for integration.

LRF1200A1 Specifications

LRF1200A1 LRF1200A1 Specifications
ParameterSpecification & conditions
Laser wavelength905 nm
Measurement range5–1,200 mBuilding target; the source table gives ≥5–1200 m.
Ranging accuracy±1 m (5 m ≤ L ≤ 100 m); ±(1 + 0.004L) m (L > 100 m)L is distance in meters.
Display resolution0.1 mReporting increment, not ranging accuracy.
Measurement update rate1–3 Hz
Communication interfaceUART, 3.3 V TTL
Supply voltage3.3 V ± 0.1 V
Standby power consumption≤400 mW
Operating power consumption≤1.5 W
Startup time≤500 ms
DimensionsØ23 × 40 mmCylindrical; use the drawing tolerances.
Weight18 g
Operating temperature−20 °C to +60 °C
Storage temperature−55 °C to +65 °C
Ingress protectionIP67Lens only.
Laser safety classClass 1As stated in the model manual; finished-equipment assessment is separate.
Transmitter lens diameterØ6.6 mm
Receiver lens diameterØ18 mm

Documents

Document notes & versions
ENGINEERING FILES

Technical Downloads

Use the current document revision for design review and confirm the ordered connector and mechanical configuration before release.

Product overview

LRF1200A1 905 nm Laser Rangefinder Module

LRF1200A1 is a laser rangefinder module for OEM integration, with a published test range of 1.2 km and a UART interface. Confirm target conditions, configuration and the current datasheet before integration.

LRF1200A1 is an 18 g cylindrical 905 nm module listing 5–1200 m on buildings at 1–3 Hz and standby power ≤400 mW, for low-rate handheld and fixed products. Several source documents disagree, so we confirm the delivered version before quotation.

WhatsApp about LRF1200A1
From $35 USD / unitLowest published unit price at 501+ pieces. Shipping included.
B2B PURCHASING

Volume Pricing

Published unit prices apply only to the stated quantity band. Configuration, qualification, tax and Incoterm details are confirmed in the quotation.

USD / unit
1–30 piecesBase tier$90 USDPublished unit price
31–200 pieces$70 USDSave 22%
201–500 pieces$50 USDSave 44%
501+ piecesLowest unit price$35 USDLowest published price · Save 61%
Commercial terms and lead time are confirmed in the quotation.

Integration library

Go into the details.

Drawings, test conditions and application notes. Open the part you need.

Selection
SELECTION

Choosing LRF1200A1 against nearby models

For a published, consistent envelope at the same range, the E family (LR1200E2, LR1200E4) is the safer choice for new designs.

If you need a cylinder, LR1200D23 (Ø23 × 45.6 mm) lists IP67 lens protection and 2–10 Hz.

Published unit prices start at $35 at 501+ pieces; see Volume Pricing for all quantity bands.

Technical documentation & drawings
SPECIFICATIONS

LRF1200A1 datasheet values

Figures are reproduced from the LRF1200A1 datasheet. Read each value together with the test condition printed beside it.

ParameterValueConditions / notes
Laser wavelength905 nm—
Measurement range5–1200 mBuilding target; the source table gives ≥5–1200 m.
Ranging accuracy±1 m (5 m ≤ L ≤ 100 m); ±(1 + 0.004L) m (L > 100 m)L is distance in meters.
Display resolution0.1 mReporting increment, not ranging accuracy.
Measurement update rate1–3 Hz—
Communication interfaceUART, 3.3 V TTL—
Supply voltage3.3 V ± 0.1 V—
Standby power consumption≤400 mW—
Operating power consumption≤1.5 W—
Startup time≤500 ms—
DimensionsØ23 × 40 mmCylindrical; use the drawing tolerances.
Weight18 g—
Operating temperature−20 °C to +60 °C—
Storage temperature−55 °C to +65 °C—
Ingress protectionIP67Lens only.
Laser safety classClass 1As stated in the model manual; finished-equipment assessment is separate.
Transmitter lens diameterØ6.6 mm—
Receiver lens diameterØ18 mm—

Operation and Data Output

The host uses the serial communication protocol to operate the ranging module. The low-power mode turns the controller off, so it does not respond to normal commands while asleep.

The manual describes an active-low enable input for normal operation and a high level for low-power mode. Use the LRF1200A1 interface and timing definitions rather than an E-series wiring assumption.

Electrical Interface

PinSignalFunction
1GNDPower ground
2Power Supply3.3 V DC input; specified supply tolerance: ±0.1 V
3NCNot connected
4TTL_TXDTransmit data: module → host; 3.3 V TTL
5TTL_RXDReceive data: host → module; 3.3 V TTL
6Enable PinActive low: normal operation. High level: low-power mode.

Mechanical Dimensions

Use the drawing and its tolerances for installation. This drawing is reproduced directly from the current LRF1200A1 user manual.

LRF1200A1 mechanical drawing, current user manual page 5
LRF1200A1 Mechanical DrawingManual page 5. Open the PDF to inspect the original dimensions and tolerances.
Integration checklist
INTEGRATION

Integrating LRF1200A1 into your design

  • Supply: 3.3 V ± 0.1 V. Do not apply 5 V.
  • Mechanics: Ø23 × 40 mm. Use the drawing supplied with your order.
  • UART at 3.3 V TTL. The manual notes that send and receive verification bytes may differ; validate the protocol on a sample before release.
  • Operating temperature: −20 °C to +60 °C.
Applications
APPLICATIONS

Where LRF1200A1 is used

  • Low-rate handhelds. Single readings on demand.
  • Fixed distance checks. Periodic measurement of slow-moving targets.
  • Legacy replacements. Matching existing Ø23 mm mounts.
Questions & answers
FAQ

LRF1200A1 integration questions

Which length is correct, 40 or 48 mm?

Both appear in source documents. We confirm the delivered drawing before you order.

Can I power it from 5 V?

Not until confirmed; the current table gives 3.3 V ± 0.1 V.

What accuracy is stated?

±1 m from 5 m to 100 m and ±(1 + 0.004L) m beyond.

HARDWARE

LRF1200A1 mounting, wiring and commands

Taken from the LRF1200A1 outline drawing and user manual. Check hole positions against the drawing or the STEP file before machining a bracket.

Mounting

Mounting-hole dimensions for this model are supplied with the outline drawing and STEP model on request.

Request the LRF1200A1 STEP model for your bracket design.

Serial settings

Logic level
3.3 V TTL
Default baud rate
115200 bit/s
Checksum
Send frames: low 8 bits of the sum of bytes 3 to 7. Reply frames: low 8 bits of the sum of bytes 1 to 7.

Common commands

CommandSend (hex)Reply (hex)Notes
Single measurement55 AA 88 FF FF FF FF 8455 AA 88 STA FF DIS_H DIS_L SUM[1:7]STA = 1: success. DIS_H/DIS_L = distance high/low byte; the reported value is 10 x the measured value.
Stop measurement55 AA 8E FF FF FF FF 8A55 AA 8E STA FF FF FF SUM[1:7]STA = 1: stopped; STA = 0: failed.

Frames follow the LRF1200A1 user manual; every full frame has been checked against the manual's checksum rule. Open-source drivers: Drivers & wiring.

Engineering Q&A

Questions about LRF1200A1

Answered by ERDI engineers in the community.

Ask an engineer about LRF1200A1

LRF1200A1 quick answers

What are the LRF1200A1 dimensions?
Ø23 × 40 mm.
How much does the LRF1200A1 weigh?
18 g.
What power does the LRF1200A1 need?
Supply: 3.3 V ± 0.1 V.
Which interface does the LRF1200A1 use?
UART, 3.3 V TTL.
How much does one LRF1200A1 cost?
$90 for 1 piece, shipping included. Volume price from $35 at 501+ pieces.
What is the minimum order for the LRF1200A1?
1 piece. Pay online by card or PayPal, or by bank transfer; shipping is free worldwide.
What is the LRF1200A1 lead time?
Standard warranty: one year. The lead time is stated on your proforma invoice (PI) before you pay.

Laser safety & status

Laser class
Class 1 (IEC 60825-1)
Status
Available to order

Laser class as stated in the module document. Classification of your finished product depends on its optical path and configuration.

ERDI TECH

Manufacturer · Chengdu · Founded 2021

Evidence-backed certifications: ISO 9001 · CE EMC

Technical inquiry

Discuss LRF1200A1 for your application.

Share the target, range, interface and expected quantity. Your selected model stays attached to the inquiry.

Request a review or quotation

Start with your work email and one line about the module or application. Add technical details if you have them.

No models attached.Name the models you are comparing in the requirement, or send the requirement without one.
Send me
Add technical requirements (optional)
Add project & contact details (optional)
Preparing the form. You can also send your request by email.

We reply within one business day (Chengdu, UTC+8).