Last updated 18 November 2026 by ERDI LASER (ERDI TECH LTD).
The Benewake TFA1500-L is a 1,500 m single-point sensor of 11 g that runs at up to 800 Hz and is built for inspection drones, payloads and surveying. ERDI LASER (ERDI TECH LTD) has two 905 nm modules at the same range: LRF1500H, which matches it on rate, and LR1500E2, which matches it on weight and supply and costs far less, but updates at only a few hertz. Neither is a copy. This page puts the figures side by side, says where the TFA1500-L is ahead, and links the rest of the laser rangefinder module range.
Specification comparison
| Parameter | Benewake TFA1500-L (source) | LRF1500H | LR1500E2 |
|---|---|---|---|
| Range | 0.5 to 1,500 m (maximum; conditions not on the page) | 0.05 to 1,500 m at 90% reflectivity; 0.05 to 300 m at 10% | 4 to 1,500 m (source table); up to 1,800 m at night |
| Update rate | 800 Hz close range; 60 Hz at long range (adaptive) | 1 kHz or 50 Hz, switched by return signal | 2 to 10 Hz adaptive |
| Accuracy | +/- 0.5 m up to 80 m; +/- 1.0 m beyond 80 m | +/- 10 cm below 10 m; 1% from 10 m | +/- 1 m (6 to 500 m); +/- (0.5 m + 0.001 D) from 500 to 1,500 m |
| Field of view / divergence | About 6 mrad | Not listed in the record | Under 6 mrad |
| Interface | UART, TTL 3.3 V, 500,000 bps | UART and I2C | UART-TTL, 115200 bps |
| Supply | Not stated on the page | 9 to 36 V DC | 3.3 to 5 V DC |
| Power | 1.8 W or less | See datasheet | About 1 W operating |
| Size | 25 x 26 x 13 mm or less | 33 x 34 x 18 mm | 25.7 x 13.3 x 24.6 mm |
| Weight | 11 +/- 0.5 g | 20 +/- 2 g | 10 g or less |
| Operating temperature | -20 to +60 degrees C | -20 to +60 degrees C | -20 to +55 degrees C (-40 custom) |
| Autopilot support | Native PX4 and ArduPilot (stated) | Driver pull request open; reference drivers on GitHub | Same |
| Price (USD) | Not published on the page | $400 for 1 to 30 pieces, $180 at 501+ pieces, shipping included | $100 for 1 to 30 pieces, $40 at 501+ pieces, shipping included |
Which one fits which job
TFA1500-L fits a drone or payload that needs a fast loop at long range: terrain follow, structure inspection, position hold. It combines 11 g, 3.3 V UART, an 800 Hz near-field rate and native autopilot support. If your flight controller already has the Benewake driver, that is a real saving in time.
LRF1500H fits a build that needs the rate but not the 3.3 V rail: it can run at 1 kHz, reaches 1,500 m on a 90% target (300 m on a dark 10% one), and costs $400 for 1 to 30 pieces. It weighs 9 g more and needs 9 to 36 V.
LR1500E2 fits ranging a fixed or slow target at 1 km class distance where weight, supply and cost matter more than rate. It weighs 10 g or less, runs on 3.3 to 5 V, and costs $100 for 1 to 30 pieces or $40 at 501+ pieces. It has a 4 m blind zone and updates at 2 to 10 Hz, so it does not suit a fast control loop.
Where we fall short
- Rate at 5 V. The only ERDI LASER 1,500 m module that reaches kilohertz rates needs 9 to 36 V.
- Autopilot ecosystem. Benewake states native PX4 and ArduPilot support. Ours is a pull request and reference drivers.
- Near range. The LR1500E2 blind zone is 4 m; the TFA1500-L lists 0.5 m.
- Unverified conditions. Benewake prints 1,500 m as a maximum without target conditions on its page, so a like-for-like range claim is not possible from public data. Ask both makers for the test target, reflectivity and visibility in writing.
Where ERDI LASER is ahead
- Price. Published per quantity with shipping included. LR1500E2 falls to $40 at 501+ pieces.
- Range options above 1,500 m. LRF3000A1 reaches 3,000 m on a building target at 70% reflectivity in clear weather (visibility 4 km or more), 12 +/- 0.5 g, 3.3 to 5 V, $200 for 1 to 30 pieces. For 4 km and more see the 1535 nm modules such as LRF0305C.
- Documents. Datasheets and the serial protocol are public and free.
Integration notes
- LRF1500H: UART at 460,800 baud by default (adjustable), frame header 0x5C, distance as a three-byte little-endian value in centimetres.
- LR1500E2: UART at 115200 bps, 8-byte frames. Lens cavity listed as IP67 in the source; confirm what that covers before outdoor use.
- Wiring examples: Pixhawk and ArduPilot, PX4.
Frequently asked questions
What is an alternative to the Benewake TFA1500-L?
From ERDI LASER, LRF1500H (0.05 to 1,500 m at 90% reflectivity, 1 kHz or 50 Hz) is the closest on update rate, and LR1500E2 (4 to 1,500 m, 3.3 to 5 V, 10 g or less) is the closest on size and supply. Neither matches every TFA1500-L figure.
Which one has the faster update rate?
The TFA1500-L runs 800 Hz close in and 60 Hz at long range. LRF1500H switches between 1 kHz and 50 Hz according to return signal strength. LR1500E2 runs 2 to 10 Hz.
Which one is lighter?
TFA1500-L is 11 +/- 0.5 g and 25 x 26 x 13 mm or less. LR1500E2 is 10 g or less (25.7 x 13.3 x 24.6 mm). LRF1500H is 20 +/- 2 g (33 x 34 x 18 mm).
Can I power LRF1500H from 5 V?
No. LRF1500H takes 9 to 36 V DC. LR1500E2 takes 3.3 to 5 V and the TFA1500-L outputs 3.3 V TTL UART.
Does ERDI LASER have PX4 or ArduPilot support?
Not as a built-in driver yet. A driver pull request to ArduPilot (#34983) was open on 13 November 2026, and reference drivers are on GitHub at ErdiTech/erdi-lrf-drivers. Benewake states native PX4 and ArduPilot support for the TFA1500-L.
What does the TFA1500-L cost?
Benewake does not publish a price on the product page (read 18 November 2026). ERDI LASER: LRF1500H is $400 for 1 to 30 pieces, $180 at 501+ pieces, shipping included; LR1500E2 is $100 for 1 to 30 pieces, $40 at 501+ pieces, shipping included.
Where to go next
Back to the laser rangefinder module hub. Model pages: LRF1500H, LR1500E2, LRF3000A1, LRF1200A1. See the other comparisons, the UAV and gimbal modules page and the 905 nm vs 1535 nm guide.
For a quote, a sample or a selection check, email tommy@erdimail.com or use the contact page.
Sources and dates
- Benewake TFA1500-L: product page, read 18 November 2026.
- ERDI values: model pages, datasheets and the published catalog; prices checked 18 November 2026.
Competitor values are the ones printed on the maker’s public page on the date shown. They may change, and test conditions differ between makers, so confirm against the current datasheet before you design in either part.