Skip to main content
Explore ERDILRF

Press ↑↓ to move, Enter to open, Esc to close.

LightWare GRF-500 Alternative (2026): LRF600H

The LightWare GRF-500 is a 500 m, 10.7 g, 35 x 31 x 21 mm rangefinder for gimbals at $459.00 excluding taxes. Two ERDI parts sit near it: the LRF600H reaches 600 m at 90% reflectivity for $350 at 1 to 30 pieces, and the LR1000E2 is 10 g or less with a 4 to 1,000 m range for $80. Both include shipping.

Specification comparison

ParameterLightWare GRF-500 (source)LRF600HLR1000E2
Wavelength905 nm905 nm905 +/- 5 nm
Range0.2 to 500 m (5 Hz, 40% albedo, 23 km visibility, 4 x 4 m target)0.05 to 600 m at 90% reflectivity; 0.05 to 200 m at 10%4 to 1,000 m (standard range; reach depends on target and environment)
Update rate0.5 to 10 readings per second1 kHz or 50 Hz, switched automatically with signal strength3 to 10 Hz, adaptive
Accuracy+/- 50 cm (1 sigma)±10 cm (<10 m); 1% (≥10 m)+/- 1 m up to 400 m; +/- (1 + 0.001 D) m beyond
Weight10.7 g20 +/- 2 g10 g or less
Size35 x 31 x 21 mm33 x 34 x 18 mm25.7 x 13.3 x 24.6 mm
InterfacesUSB, serial UART, I2C (3.3 V TTL, 5 V tolerant)UART / I2CUART-TTL
Supply and power0.6 W9 to 36 V DC; 1.2 W average3.3 to 5 V; 1 W or less in operation; under 1 mW asleep
Operating temperature-20 to 60 C-20 to +60 C-20 to +55 C
Price (USD)$459.00 excl. taxes$350 for 1 to 30 pcs; $160 from 501 pcs$80 for 1 to 30 pcs; $30 from 501 pcs

Which one fits which job

GRF-500 was designed for small EO/IR gimbals: it comes with a defined boresight tolerance (+/- 1.5 degrees to its mechanical interface), USB for setup and a 3.3 V logic interface. LRF600H suits a larger payload with a 12 or 24 V rail where 600 m on a bright target and an automatic 1 kHz or 50 Hz mode are useful. LR1000E2 is the closest on weight and gives a longer 1,000 m range from a 3.3 to 5 V supply, but its minimum range is 4 m and its accuracy figure is looser (+/- 1 m).

Price

LightWare lists $459.00 excluding taxes (page read 2026-11-13, shown as available on backorder). ERDI: LRF600H is $350 for 1 to 30 pieces, $200 for 31 to 300, $180 for 301 to 500 and $160 from 501. LR1000E2 is $80 for 1 to 30, $60 for 31 to 200, $40 for 201 to 500 and $30 from 501. Shipping is included.

Integration notes

  • LRF600H: UART 460,800 baud default (adjustable), 8N1, header 0x5C. The datasheet gives a 9 to 36 V supply and does not state the UART signal level, so confirm it with us.
  • LR1000E2: UART-TTL at 115,200 baud, 8-byte frames with header 55 AA and a sum checksum. Its mechanical drawing is 25.7 x 13.3 x 24.6 mm and the lens cavity is IP67.
  • Mass budget for gimbal payloads: see the article on rangefinder mass budget and the UAV gimbal module page.

Sources and dates

Competitor values are the ones printed on the maker’s public page on the date shown. They may change, and test conditions differ between makers, so confirm against the current datasheet before you design in either part.

Frequently asked questions

Is there a lower-cost alternative to the LightWare GRF-500?

ERDI LRF600H (600 m at 90% reflectivity) is $350 at 1 to 30 pieces and LR1000E2 (up to 1,000 m, 10 g or less) is $80, shipping included. The GRF-500 is $459.00 excluding taxes on LightWare’s page (read 2026-11-13).

Which ERDI module is closest to the GRF-500 in weight?

The LR1000E2 at 10 g or less, against 10.7 g for the GRF-500. The LRF600H is 20 g.

Does the ERDI LR1000E2 have USB or I2C like the GRF-500?

No. The LR1000E2 has a UART-TTL interface only, at 115,200 baud. USB and I2C on the GRF-500 are listed by LightWare.

What supply voltage does the ERDI LR1000E2 need?

3.3 to 5 V. The LRF600H needs 9 to 36 V DC.

How accurate is the ERDI LR1000E2 compared with the GRF-500?

The LR1000E2 is specified at +/- 1 m up to 400 m and +/- (1 + 0.001 D) m beyond. LightWare lists +/- 50 cm (1 sigma) for the GRF-500 at its stated test condition.

Where to go next

Model pages: LRF600H, LR1000E2, LR1200E2, LRF0305C. To filter the whole range by distance, wavelength and interface, use the selector. Other comparisons are on the comparison hub, and every model price is on the price page. For a quote or a sample, email tommy@erdimail.com or use the contact page.