Skip to main content
Explore ERDILRF

Press ↑↓ to move, Enter to open, Esc to close.

LightWare SF30/D Alternative (2026): LRF200H

LightWare lists the SF30/D at 200 m, 30 g, with USB, UART and I2C and up to 20,000 readings per second, for $459.00 excluding taxes. The closest ERDI part is the LRF200H: 200 m at 90% reflectivity, 20 g, UART and I2C, $250 for 1 to 19 pieces with shipping included. The SF30/D has the faster update rate and first and last pulse output; the LRF200H costs $209 less per unit at one piece.

Specification comparison

ParameterLightWare SF30/D (source)LRF200H
Wavelength905 nm905 nm
Range0.2 to 200 m (maximum range on 70% reflectivity targets)0.05 to 200 m at 90% reflectivity; 0.05 to 70 m at 10%
Update rate39 to 20,000 readings per second20 Hz to 10 kHz (default 1 kHz)
Signal processingFirst and last pulse availableOne distance value per reading (no first and last pulse mode listed)
AccuracyNot stated in the shop specification±10 cm (<10 m); 1% (≥10 m)
InterfacesUSB, serial UART and I2C (3.3 V TTL, 5 V tolerant)UART, I2C
SupplyNot stated in the shop specification9 to 36 V DC; 30 mA average, 0.7 W
Weight30 g20 +/- 2 g
Size30 x 56 x 50 mm33 x 34 x 18 mm
Integration listedPX4, ArduPilot, Arduino, Raspberry Pi, LW StudioDocumented UART and I2C protocol; reference drivers on GitHub
Price (USD)$459.00 excl. taxes$250 for 1 to 19 pcs; $100 from 999 pcs, shipping included

Which one fits which job

SF30/D fits flight work that needs very high update rates or first and last pulse returns, for example altitude above water or terrain following, with PX4 and ArduPilot support already in place and a USB interface for bench setup. LRF200H fits a build where unit cost, weight and board area matter and a 1 kHz default rate is enough: it is 10 g lighter, about a quarter of the volume by the listed sizes, and runs from a 12 or 24 V rail.

Price

LightWare shows $459.00 excluding taxes on its shop page (page read 2026-11-13, status shown as available on backorder). ERDI prices LRF200H at $250 for 1 to 19 pieces, $240 for 20 to 30, $150 for 31 to 500, $130 for 501 to 998 and $100 from 999. Shipping is included in every ERDI figure.

Integration notes

  • LRF200H: UART at 460,800 baud by default (adjustable), 8N1, frame header 0x5C. The I2C default address is 0x33 and the bus speed runs from 1 kHz to 400 kHz, per the datasheet.
  • The datasheet states a 9 to 36 V supply but not the UART signal level. Confirm it with us before you connect to a 3.3 V host.
  • Wire: 1.25 mm, 5-pin, 50 cm stranded. Class 1 laser, field of view about 4 mrad.
  • There is also a shorter write-up on the SF30/D alternative page and a general ERDI vs LightWare article.

Sources and dates

Competitor values are the ones printed on the maker’s public page on the date shown. They may change, and test conditions differ between makers, so confirm against the current datasheet before you design in either part.

Frequently asked questions

What is a cheaper alternative to the LightWare SF30/D?

ERDI LRF200H is a 200 m module at $250 for 1 to 19 pieces, shipping included, against $459.00 excluding taxes for the SF30/D on LightWare’s shop page (read 2026-11-13). It does not offer first and last pulse output or USB.

Does the ERDI LRF200H give the same update rate as the SF30/D?

No. LightWare lists up to 20,000 readings per second. The LRF200H runs 20 Hz to 10 kHz with a 1 kHz default.

Can the ERDI LRF200H run on 5 V?

No. It takes 9 to 36 V DC. For a 3.3 to 5 V supply look at the LR1000E2 (up to 1,000 m, 3.3 to 5 V) or the LRF50VB (50 m).

Does ArduPilot or PX4 support the ERDI LRF200H?

Not as a built-in driver yet. A driver pull request to ArduPilot (#34983) was open on 2026-11-13. The UART and I2C protocol is documented, and reference drivers are on GitHub at ErdiTech/erdi-lrf-drivers.

What range does the ERDI LRF200H reach on a dark target?

The datasheet lists 0.05 to 200 m at 90% reflectivity and 0.05 to 70 m at 10% reflectivity. LightWare quotes its 200 m on 70% reflectivity targets, so compare the conditions first.

Where to go next

Model pages: LRF200H, LRF300H, LRF600H, LR1000E2. To filter the whole range by distance, wavelength and interface, use the selector. Other comparisons are on the comparison hub, and every model price is on the price page. For a quote or a sample, email tommy@erdimail.com or use the contact page.